Description
Malossi Lambda Emulator
Improving carburation means improving performance: Malossi Lambda Emulator TC Unit O2 Controller Yamaha Tmax 560, adjusts fuel / air mixture to increase performance in tuned engines. In original engine set-ups, air / fuel ratio is automatically adjusted via lambda sensor and CDI, but in a tuned engine, you might want to see better results.
The Malossi lambda emulator is plugged between lambda sensor and lambda control module / ECU. It simulates the signal of the original sensor and modifies it so air-fuel mixture for tuned motor set-ups can be adjusted and improved. The air / fuel mixture becomes more stable, even in closed loop condition.
Features Malossi tc unit O2 Emulator:
- Air-fuel optimization: adjusts the air-fuel ratio to improve engine performance.
- Compatibility: Used with the original lambda sensor, which guarantees a precise simulation of the signals.
- Easy installation: Is placed between the lambda sensor and control unit, no modifications required.
- Full control: Can be combined with the Malossi Force Master CDI ECU for full control of the combustion process.
- LED telltales: Status LEDs show the correct fuel supply and carburetor ratio in real time.
Technical data Lambda O2 controller:
- Model: TC Unit O2 Malossi
- Compatibility: Fantic Caballero 125 ie 4T LC Euro 5, Fantic Enduro / Motard 125 ie 4T LC Euro 5, Yamaha MT / NMax 125 ie 4T LC Euro 5, Yamaha Tmax 530 ie 4T LC (after 2012), Yamaha TMax 560 ie 4T LC Euro 5, Beta RR Enduro 125 ie 4T LC Euro 5, etc.
CDI and coil
The CDI (for Capacitor Discharger Ignition) and the ignition coil are an essential part of the ignition. While the coil is actually just an energy storage device that supplies the ignition spark to the spark plug, the CDI module is a more complex component that controls the engine speed at which the spark should occur. It can therefore have an effect on engine behavior and performance.
Open CDI
Many riders equip their 50cc geared mopeds and scooters with open, i.e. derestricted CDIs. In most cases, the original CDI throttles the maximum achievable engine speed, which significantly reduces performance and top speed.
To remove this rev limiter and thus increase maximum speed, you can install a CDI without a rev limiter instead of the original CDI.
Beware! When using an open CDI, the carburetor must be readjusted, so it is best to order new jets as well.
Programmable CDI
Programmable CDI control units are available for tuned racing engines on 50cc scooters and moorcycles as well as for motocross bikes. These CDIs are designed for more experienced tuners who want to optimize the settings of their two-wheeler as much as possible.
With a programmable CDI, the ignition timing is dynamic so that the spark always jumps at the optimum time at both high and low engine speeds. This leads to a better increase in speed, higher torque and an overall increase in maximum power.
4-stroke engines with fuel injection are equipped with an ECU (Electronic Control Unit), which also controls the fuel injection. When tuning a four-stroke engine with an electronic injection system, a programmable CDI is therefore an absolute must in order to avoid breakdowns and engine damage.
Symptoms of a defective coil or CDI
If these two elements fail, the symptoms are usually very easy to recognize: no spark at the spark plug, so the engine will not start.
It is best to proceed in sequence: First change the spark plug, then the spark plug cap, then the coil and only then consider the CDI or the ignition itself as the source.
| Lambda Sensor Malossi Yamaha Tmax 560 | |
|---|---|
| Article no. | M5519172B |
| Weight | 0,20 kg |
| Series | TC Unit |
| Brand | Malossi |
| Product type | Ignition coil & CDI |
| Power supply lighting | Without power supply |